Zhejiang Arbueo Intelligent Equipment Manufacturing Co., Ltd.

How to avoid air bubbles in products made by a single phase injection moulding machine?

Apr 03, 2026Leave a message

In the manufacturing process using a single phase injection moulding machine, air bubbles in the final products can be a persistent and frustrating issue. As a trusted supplier of Single Phase Injection Moulding Machines, I understand the challenges manufacturers face when dealing with this problem. In this blog, I will share some effective strategies to avoid air bubbles in products made by a single phase injection moulding machine.

Understanding the Causes of Air Bubbles

Before we can address the issue of air bubbles, it's crucial to understand what causes them. There are several factors that can lead to the formation of air bubbles during the injection moulding process:

1. Moisture in the Resin

Plastic resins can absorb moisture from the environment, especially if they are not stored properly. When the resin is heated during the injection moulding process, the moisture turns into steam, which can form air bubbles in the product.

2. Improper Venting

The mould needs to have proper venting to allow the air to escape during the injection process. If the vents are blocked or not designed correctly, air can get trapped inside the mould, resulting in air bubbles in the product.

3. High Injection Speed

Injecting the molten plastic too quickly can cause the plastic to flow turbulently, trapping air in the process. This can lead to the formation of air bubbles in the final product.

4. Low Melt Temperature

If the plastic is not melted to the correct temperature, it may not flow smoothly into the mould. This can cause air to be trapped in the plastic, resulting in air bubbles.

Strategies to Avoid Air Bubbles

1. Proper Resin Drying

To prevent moisture from causing air bubbles, it's essential to dry the plastic resin thoroughly before use. Most plastic resins have specific drying requirements, including temperature and time. You can use a resin dryer to ensure that the resin is dried to the appropriate moisture level. For example, PET resin typically needs to be dried at a temperature of around 120 - 150°C for 4 - 6 hours.

2. Optimize Mould Venting

The design and maintenance of the mould vents are critical. The vents should be placed in areas where air is most likely to be trapped, such as at the end of the flow path or in areas with complex geometries. Regularly clean the vents to prevent them from getting blocked by plastic or debris. You can also consider using a venting agent or a porous mould material to improve venting.

3. Adjust Injection Speed

Finding the right injection speed is crucial. Injecting the plastic too slowly can cause the plastic to cool and solidify before filling the mould completely, while injecting it too quickly can trap air. You may need to conduct some tests to determine the optimal injection speed for your specific product and material. Start with a relatively low speed and gradually increase it until you find the speed that allows the plastic to fill the mould without trapping air.

4. Control Melt Temperature

Maintaining the correct melt temperature is essential for ensuring the smooth flow of the plastic. If the temperature is too low, the plastic may not flow properly and can trap air. On the other hand, if the temperature is too high, the plastic may degrade, also leading to product defects. Refer to the material supplier's recommendations for the appropriate melt temperature range and use temperature controllers on your injection moulding machine to maintain a consistent temperature.

5. Check the Injection Pressure

Inadequate injection pressure can result in incomplete filling of the mould, which can lead to air pockets. However, excessive injection pressure can also cause problems, such as flash or warping. Adjust the injection pressure based on the size and complexity of the product, as well as the properties of the plastic material.

6. Use Vacuum Moulding

Vacuum moulding is a technique that can be very effective in reducing air bubbles. By creating a vacuum inside the mould before injecting the plastic, you can remove most of the air, preventing it from getting trapped in the product. This technique is particularly useful for products with high precision requirements.

Table Top Plastic Injection Molding MachineHot Runner Injection Molding Machine

The Role of Our Single Phase Injection Moulding Machines

Our Single Phase Injection Moulding Machines are designed with advanced features to help you minimize the occurrence of air bubbles in your products. These machines offer precise control over injection speed, pressure, and temperature, allowing you to optimize the injection process for different materials and product designs.

We also provide a range of related products that can further enhance your injection moulding operations. For example, our Hot Runner Injection Molding Machine is designed to keep the plastic in a molten state throughout the injection process, reducing the risk of air bubbles and improving the quality of the final product. Our Table Top Plastic Injection Molding Machine is a compact and cost - effective solution for small - scale production, while our PE PP PC PET Plastic Injection Molding Machine is specifically designed for processing these common plastic materials.

Conclusion

Avoiding air bubbles in products made by a single phase injection moulding machine requires a combination of proper material handling, mould design, and machine operation. By following the strategies outlined in this blog, you can significantly reduce the occurrence of air bubbles and improve the quality of your products.

If you are facing challenges with air bubbles in your injection moulding process or are looking to upgrade your equipment, we are here to help. Our team of experts can provide you with personalized advice and solutions based on your specific needs. Don't hesitate to contact us to start a discussion about your injection moulding requirements.

References

  • "Injection Molding Handbook" by O. Olafsson
  • "Plastics Processing Technology" by J. Beaumont