Zhejiang Arbueo Intelligent Equipment Manufacturing Co., Ltd.

How to solve the sink mark problem in injection molding?

Apr 24, 2026Leave a message

Hey there, fellow injection molding enthusiasts! Today, I'm gonna talk about one of the most annoying issues in the injection molding world: sink marks. As an injection machine supplier, I've seen this problem pop up time and time again, and I'm here to share some tips on how to solve it.

What are Sink Marks in Injection Molding?

First off, let's quickly go over what sink marks are. Sink marks are small, shallow depressions that appear on the surface of an injection - molded part. They usually show up in areas where the part is thick or has ribs, bosses, or other features that cause uneven cooling. When the plastic cools and solidifies, it shrinks. In thick sections, the plastic takes longer to cool, and as it shrinks, it pulls away from the mold surface, leaving those unsightly sink marks.

Causes of Sink Marks

There are several factors that can cause sink marks. Understanding these causes is the first step in solving the problem.

1. Wall Thickness Variations

As I mentioned earlier, thick sections of a part cool more slowly than thin sections. When a thick area finally cools and shrinks, it creates a sink mark. For example, if you have a part with a large boss attached to a thin wall, the boss will cool slower, and the shrinking of the boss material can pull on the surrounding thin wall, leading to a sink mark.

2. Injection Pressure and Time

Insufficient injection pressure can also result in sink marks. If the pressure isn't high enough, the mold cavity won't be filled completely, and as the plastic cools and shrinks, there won't be enough material to compensate for the volume loss. Similarly, if the injection time is too short, the plastic may not have enough time to properly pack and fill the mold, increasing the likelihood of sink marks.

3. Cooling Time

Improper cooling time can play a big role. If the part is ejected from the mold too soon, the plastic is still in a semi - molten state and can continue to shrink, causing sink marks. On the other hand, if the cooling time is too long, it can increase production cycle times and may also cause other issues, but it can sometimes help reduce sink marks as the plastic has more time to solidify uniformly.

Single Phase Injection Moulding MachinePu Injection Moulding Machine

4. Mold Design

The mold design can contribute to sink marks. For example, if the gate location is not well - chosen, the plastic flow may be uneven, leading to uneven cooling and sink marks. Also, a lack of proper venting in the mold can trap air, which can prevent the plastic from filling the cavity completely and result in sink marks.

How to Solve the Sink Mark Problem

Now that we know what causes sink marks, let's look at some ways to solve this problem.

1. Optimize Part Design

  • Uniform Wall Thickness: Try to keep the wall thickness as uniform as possible throughout the part. If you need to have thick sections, consider using ribs or bosses with a more gradual transition to the thinner walls. This can help reduce the difference in cooling rates and minimize sink marks.
  • Hollow Structures: In some cases, using hollow structures instead of solid thick sections can be a great solution. Hollow parts cool more quickly and evenly, reducing the risk of sink marks.

2. Adjust Injection Parameters

  • Increase Injection Pressure: By increasing the injection pressure, you can ensure that the mold cavity is filled more completely. This helps to pack more material into the thick sections, compensating for the shrinkage during cooling. However, be careful not to increase the pressure too much as it can cause other problems like flash or excessive stress on the mold.
  • Extend Injection Time: A longer injection time allows the plastic to flow more evenly and pack the mold better. This can help prevent sink marks by ensuring that there is enough material in the thick sections of the part.

3. Control Cooling Time

  • Proper Cooling Schedule: Set an appropriate cooling time based on the part design and the type of plastic being used. You can use cooling analysis software to optimize the cooling time and ensure that the plastic solidifies uniformly. Sometimes, using a cooling mold with a more efficient cooling system, like a water - cooled mold, can help regulate the temperature and reduce sink marks.
  • Cooling Rate: Controlling the cooling rate is also important. Slow cooling can sometimes reduce the risk of sink marks, but it can increase production time. On the other hand, rapid cooling can cause internal stresses and warping. You need to find a balance that works for your specific part.

4. Improve Mold Design

  • Gate Location: Select the gate location carefully to ensure even plastic flow. A well - placed gate can help the plastic fill the mold cavity uniformly, reducing the chances of uneven cooling and sink marks. You may need to use simulation software to determine the best gate location for your part.
  • Venting: Make sure the mold has proper venting. Venting allows air to escape from the mold cavity during the injection process, ensuring that the plastic can fill the cavity completely. This helps prevent sink marks caused by trapped air.

Our Injection Machines and Sink Mark Solutions

At our company, we offer a variety of injection machines that can help you tackle the sink mark problem. For example, our Polyurethane Foam Injection Molding Machine is designed to provide precise control over the injection process. It can handle polyurethane foam materials with high accuracy, allowing you to adjust the injection pressure, time, and cooling parameters to minimize sink marks.

Our Single Phase Injection Moulding Machine is another great option. It's suitable for small - to - medium - sized production runs and offers user - friendly controls. You can easily fine - tune the injection settings to ensure proper filling and cooling of the mold, reducing the risk of sink marks.

And if you're working with PU materials, our Pu Injection Moulding Machine is specifically designed to meet your needs. It provides excellent performance and reliability, helping you produce high - quality parts without sink marks.

Conclusion

Sink marks can be a real headache in injection molding, but with the right approach, you can solve this problem. By optimizing part design, adjusting injection parameters, controlling cooling time, and improving mold design, you can significantly reduce the occurrence of sink marks. And remember, our injection machines are here to support you in your injection molding journey.

If you're facing sink mark issues in your injection molding process or are looking for a reliable injection machine, don't hesitate to reach out to us. We're more than happy to discuss your needs and help you find the best solution.

References

  • Throne, J. L. (1996). Plastics Property Database. Chan & Partners.
  • Rosato, D. V., Rosato, D. V., & Schicht, M. (2000). Injection Molding Handbook. Kluwer Academic Publishers.