Zhejiang Arbueo Intelligent Equipment Manufacturing Co., Ltd.

How to solve the short shot problem in injection molding?

Aug 03, 2026Leave a message

How to Solve the Short Shot Problem in Injection Molding?

Injection molding is a widely used manufacturing process for producing plastic parts in large quantities. However, one of the most common issues encountered in injection molding is the short shot problem. A short shot occurs when the molten plastic does not completely fill the mold cavity, resulting in an incomplete part. This can lead to significant production losses, increased costs, and quality issues. As an Injection Machine supplier, we understand the challenges that come with short shots and are here to share some effective solutions.

Understanding the Causes of Short Shots

Before we can address the short shot problem, it's essential to understand its root causes. There are several factors that can contribute to short shots, including:

  1. Inadequate Injection Volume: If the injection volume of the machine is not sufficient to fill the mold cavity, a short shot will occur. This could be due to incorrect machine settings or a mismatch between the machine's capacity and the size of the mold.
  2. Low Injection Speed: A slow injection speed can cause the molten plastic to cool down before it reaches all parts of the mold cavity. This can result in premature solidification and a short shot.
  3. High Viscosity of Plastic: Some plastics have a high viscosity, which means they flow less easily. This can make it difficult for the plastic to fill the mold cavity, especially in areas with thin walls or complex geometries.
  4. Mold Design Issues: Poor mold design can also contribute to short shots. For example, if the gate size is too small, the plastic may have difficulty entering the mold cavity. Similarly, if the runner system is not properly designed, it can cause pressure drops and prevent the plastic from flowing evenly.
  5. Temperature Problems: Incorrect temperatures in the barrel, nozzle, or mold can affect the flow of the molten plastic. If the temperature is too low, the plastic will be more viscous and less likely to fill the mold cavity. On the other hand, if the temperature is too high, the plastic may degrade or burn.

Solutions to the Short Shot Problem

Now that we have identified the possible causes of short shots, let's explore some solutions:

  1. Adjust the Injection Parameters:
    • Increase the Injection Volume: Check the machine settings and make sure the injection volume is sufficient to fill the mold cavity. You may need to adjust the screw stroke or the injection pressure to increase the volume.
    • Increase the Injection Speed: A higher injection speed can help the molten plastic reach all parts of the mold cavity before it cools down. However, be careful not to increase the speed too much, as this can cause other problems such as flash or air traps.
    • Optimize the Injection Pressure: The injection pressure should be high enough to overcome the resistance of the plastic flow but not so high that it causes damage to the mold or the machine. You may need to experiment with different pressure settings to find the optimal value.
  2. Modify the Plastic Material:
    • Choose a Lower Viscosity Plastic: If the high viscosity of the plastic is causing the short shot problem, consider switching to a plastic with a lower viscosity. This will make it easier for the plastic to flow and fill the mold cavity.
    • Add Plasticizers: Plasticizers can be added to the plastic to reduce its viscosity and improve its flow properties. However, be aware that adding plasticizers may also affect the mechanical properties of the final part.
  3. Improve the Mold Design:
    • Increase the Gate Size: A larger gate size can allow the plastic to enter the mold cavity more easily. However, be careful not to make the gate too large, as this can cause other problems such as gate vestiges or uneven filling.
    • Optimize the Runner System: The runner system should be designed to minimize pressure drops and ensure even flow of the plastic. This may involve using larger runners, reducing the length of the runners, or using a balanced runner system.
    • Add Venting: Proper venting is essential to allow air to escape from the mold cavity during the injection process. Without adequate venting, air can become trapped in the mold, causing short shots or other defects.
  4. Control the Temperature:
    • Check and Adjust the Barrel Temperature: Make sure the barrel temperature is set correctly for the type of plastic being used. The temperature should be high enough to melt the plastic but not so high that it causes degradation.
    • Monitor and Control the Nozzle Temperature: The nozzle temperature can also affect the flow of the plastic. Make sure the nozzle is heated to the appropriate temperature and that there are no blockages or leaks.
    • Maintain the Mold Temperature: The mold temperature should be kept within a specific range to ensure proper flow and solidification of the plastic. You may need to use a temperature control system to maintain the mold temperature.

Our Injection Machines and Their Role in Solving Short Shots

As an Injection Machine supplier, we offer a wide range of high - quality injection machines that can help you solve the short shot problem. Our Table Top Plastic Injection Molding Machine is perfect for small - scale production and prototyping. It is easy to operate and offers precise control over the injection parameters, allowing you to adjust the injection volume, speed, and pressure to prevent short shots.

Pu Injection Moulding MachinePolyurethane Foam Injection Molding Machine

Our Pu Injection Moulding Machine is specifically designed for processing polyurethane materials. It has advanced temperature control systems and high - pressure injection capabilities, which can ensure that the molten polyurethane fills the mold cavity completely, reducing the risk of short shots.

The Polyurethane Foam Injection Molding Machine we provide is ideal for producing polyurethane foam products. It has a precise mixing and dosing system, which can ensure the proper ratio of raw materials and the uniform distribution of the foam in the mold, minimizing the occurrence of short shots.

Conclusion

The short shot problem in injection molding can be a frustrating and costly issue. However, by understanding the causes and implementing the appropriate solutions, you can significantly reduce the occurrence of short shots and improve the quality and efficiency of your injection molding process. As an Injection Machine supplier, we are committed to providing you with the best - in - class injection machines and technical support to help you solve any problems you may encounter.

If you are facing short shot issues in your injection molding process or are looking to upgrade your injection machines, we invite you to contact us. We have a team of experienced professionals who can provide you with personalized solutions and advice. Let's work together to optimize your injection molding process and achieve better results.

References

  • Throne, J. L. (1996). Plastics Process Engineering. Marcel Dekker.
  • Rosato, D. V., & Rosato, D. V. (2000). Injection Molding Handbook. Kluwer Academic Publishers.
  • Osswald, T. A., & Turng, L. - S. (2007). Injection Molding Handbook. Hanser Publishers.